SECURITEX SCT TWISTED PAIR TECHNOLOGY

　

Securitex Electronic Systems Engineering

CCTV division (Twisted Pair Technology)

Twisted Pair Transmission Transceiver - Passive Series:

manufactures very high quality, unshielded twisted pair (UTP) Cat5E or Cat 6 CCTV video transmission equipment. With a new range of video transmitters and receivers for distance up to 2.4 Km. Simply find a spare pair of CAT 5 cable near the camera or source video and cross connect through the building (s) to where you plan to put your monitor, multiplexer, DVR, Digital Video Recording System or destination device. The advantages of this type of system are clear video signal, fewer cables to manage, lower cost per connection, centralized wiring for greater control. These units feature exceptional noise immunity and a new technology that allows simultaneous operation over existing UTP wiring within a building. Perfect for larger CCTV installations where need install many cameras, difficult in using coaxial cable, existing many interference environment. .Such as: School, airport, park, department, casino, elevator, hospital, parking lot, electricity plant, prison, shopping mall, traffic control...etc.

TTP111V  Video Transceiver BNC Male To RJ-45 female
Features: 

  • BNC male to RJ45 female. 

  • Transmit a full motion color or monochrome video signal up to 600 meters. 

  • Distance up to 1Km when used with an active receiver such as TTA-111V.

  • Includes CAT 5 RJ45 male to 2 screw terminal adapter. 

  • Passive, no power required.

  • Built in impedance couple device and noise filter for exceptional interference immunity.

  • Up to 16 pieces TTP-111V can work with 1U rack mounting TPP016 receiver panel.

TTP111V

TTP111VT  Video Transceiver BNC Male To Terminal Block 
Features:

  • BNC male to terminal Block.

  • The other features are identical to above.

　

　

　

　

 TTP111VF

TTP111VF  Video Transceiver F Male To Terminal Block 
Features:

  • F male to terminal Block.

  • The other features are identical to above.

　

　

　

 TTP111VT

TTP111VP  Video Transceiver BNC Male To RJ45 Female With Power Cord

Features:

  • BNC male + DC plug to RJ45 female.  

  • Use with TTP111VPJ, transmit video & power over one Cat 5 cable. (range 50meters).

  • Use with TDP414VP for power transmission 4 cameras from remote site 

　

　

 TTP111VP

　

DIY KIT: TTP111VPK ( TTP111VP + TTP111VPJ)

TTP111VPK

RJ45 pin connectTTP111VPK

RJ45 pin connect

Pair 1 : 1. Orange-white & 2. Orange

Pair 2 : 3. Green-white & 6. Green

Pair 3 : 4. Blue & 5. Blue-white → Power

Pair 4 : 7. Brown-white & 8. Brown → Video

　

　

　

TTP111VCT Video Transceiver With 18cm Retractile Cord 

Features: 

  • BNC male to screw terminals with 18cm Retractile Cord.

  • Weather Proof. IP65

  • Perfect for camera with pan-tilt turning device.

 TTP111VCT

　

　

　

　

TTP111VL Video Transceiver with 25cm mini coax cable
 Features:

  • BNC male to terminal Block. 

  • Weather Proof. IP65

  • TTP111VL compact size, perfect to connect with the image processor, which have multi BNC connections, as like Multiplexer, Quad, DVR …etc.

　

DIY KIT: TTP111VK ( TTP111VT + TTP111VL)

Network cable pin connect

1. Orange-white

2. Orange

3. Green-white

4. Blue

5. Blue-white

6. Green

7. Brown-white

8. Brown

 TTP111VK

　

　

TTP111VPD Video, Data, Power Transceiver 

Features: 　

  • Male BNC with DC Plug+2 pin pigtail to 6 “push pin” terminal.

  • Video , camera power, Data ( RS422, 485) transmission over one standard CAT 5 cable.

  • Push pin terminal for easy cable connection.

TTP111VPD

　

　

TVB001 Twisted Pair VIDEO BALUN 

Features: 　

  • Eliminate interference under long range cabling caused by "Impedance Matching", add TVB001 BALUN at "connecting point" between two-wire connections for compensation. 

  • Including 4 pieces UY connectors for connection. 

TVB001

　

　

TTP111VH Video Transceiver With Extra Interference Rejection
Features: 

  • BNC female to terminal block. 

  • Perfect work with DVR to immunity DVR interference.

  • Built in a highly balanced mode of video transmission, which is immune to interference from these, and other sources of noise: Data signals, other video signals, nearby power, ringing telephones, fluorescent lights, transformers, and more...

TTP111VH

　

　

TTP111AV  Video & Audio Transceiver

Features: 

  • BNC male + 2 RCA female to RJ45 female.

  • Video and stereo audio transmission.

Specification

 TTP111AV
ITEM TTP111VF TTP111VT TTP111VH TTP111V TTP111VCT TTP111VP TTP111AV
Video Input

(BNC Connector)

 F 1 1 1 1 1 1
Video Input 1Vp-p, 75ohms 1Vp-p, 75ohms 1Vp-p, 75ohms 1Vp-p, 75ohms 1Vp-p, 75ohms 1Vp-p, 75ohms 1Vp-p, 75ohms
Audio Input

(RCA Connector)

 X X X X X X 2Way
Audio Input X X X X X X 2V p-p
RJ-45 Input X X X X X X X
RJ-45 Output Terminal Terminal Terminal 1 1 1 1
Transmission Distance 600 M (B/W), 400M(COLOR)
Cable for RJ-45 Twisted Pair CAT 5 ( AWG 24 )
Power X X X X X X X
Dimension

W x H x D mm

 69x25x22 69x25x22 88x38x27 69x25x22 　 69x25x22 110x77x24

　

TTP414V Rear

　

TTP414V  4 Channel Video Transceiver 4 x BNC Female to 1 x RJ45 Female
Features: 

  • 4 x BNC female to 1x RJ45 female + 8 pin Terminal block

  • Four passive transceivers in one product.

TTP414V Front

　

TTP414VH  4 channel video transceiver with Extra Interference Rejection  
Features: 

  • 4 BNC female to 1 x RJ45 female. 

  • Perfect work with DVR to immunity DVR interference.

  • Built in a highly balanced mode of video transmission, which is immune to interference from these, and other sources of noise: Data signals, other video signals, nearby power, ringing telephones, fluorescent lights, transformers, and more... 

 TTP414VH
　

TTP414VD  4 Channel Video Transceiver With Data

 Features:

  • 4 x BNC female + 1 x RJ45 female + 1x terminal block ( for data transmission : pan, tilt, zoom ).

  • Using 4 pairs CAT 5 cable to transmit/receive 3 sets video signals plus 1 data signal or transmit/receive 4 sets video signals only.

 TTP414VD

　

TTP444V Front

TTP444V  4 Channel Video Transceiver  4 x BNC Female to 4 x RJ45 Female 
 Features:

  •  4 x BNC female to 4 x RJ45 female. 

  • Four passive transceivers in one product.

TTP444V Rear

　

　

TTP444VPD  4 Channel Video,  Power, Data Transceiver 
 Features:

  • 4 x BNC female + DC power to 4 x RJ45 female + 2 pin terminal for DATA.

  • Video, camera power, Data (RS422, 485) transmission over one standard CAT 5 cable.

  • Built in PTC fuse for short protection.

  • Application for color video signal up to 300 meters, B/W to 600 meters.

  • Use with TTP111VPD/VP, transmit 4 channels video, power, data over 4 CAT 5 cable.

Specification

 TTP444VPD Front

　

　

TTP444VPD Rear

ITEM

 TTP414V TTP414VH TTP414VD TTP444V

Video Input

(BNC Connector)

 4 4 4 4

Video Input

 1V p-p, 75 Ohms 1V p-p, 75 Ohms 1V p-p, 75 Ohms 1V p-p, 75 Ohms

Audio Input

(RCA Connector)

 X X X X
Audio Input X X X X

RJ-45 Input

 X X X X

RJ-45 Output

1 1 1 4

Transmission Distance

 600M(B/W), 400M(COLOR)
Cable for RJ-45 Twisted Pair CAT5 (AWG24)
Power X X X X

Dimension W x H x D mm

 110x77x24 138x66x28 138x66x28 110x77x24

　

Twisted Pair Transmission Transceiver - ACTIVE Series

Active Video Transceiver (power required), transmission range color 1500 meters, B/W 2400 meters  via CAT 5 UTP Cable. 

TTA111V  Video Twisted Pair Transceivers

TTA111VT Transmitter, TTA111VR Receiver

Features: 

  • Three position range switch for gain select on transmitter.

  • Five position distance range switch on Receiver, brightness adjustment.

  • Built in transient protection and ground lifting.

  • System is integrated with alarm sensor (PIR, Magnetic, etc...) or data (Pan, Tilt, Zoom ).

　

　

　

　

　

　

 　

TTA111AVR Rear

　

　

　

TTA111AVR - Receiver (front)

TTA111AVR Front

　

　

　

TTA111AVR - Receiver (back)

TTA111V  Video Twisted Pair Transceivers

TTA111VT Transmitter, TTA111VR Receiver

Features: 

  • Three position range switch for gain select on transmitter.

  • Five position distance range switch on Receiver, brightness adjustment.

  • Built in transient protection and ground lifting.

  • System is integrated with alarm sensor (PIR, Magnetic, etc...) or data (Pan, Tilt, Zoom ).

　

 　

　

　

　

　

TTA111AVR Rear

　

　

　

TTA111AVR - Receiver (front)

TTA111AVR Front

　

　

　

TTA111AVR - Receiver (back)

TTA111AV  Video & Audio & Data Twisted Pair Transmission

TTA111AVT Transmitter, TTA111AVR Receiver
 Features: 

  • Transmit video, audio and data signal (RS422, RS485).

  • Three position range switch for gain select on transmitter.

  • Five position distance range switch on Receiver, brightness adjustment, two video output.

  • Built in transient protection and ground lifting.

TTA111AVT Rear

TTA111AVT - Transmitter (Front)                      TTA111AVT Front

TTA111AVT - Transmitter (back)

TTA111VTTTA111VT-Transmitter

TTA111VR TTA111VR-Receiver

Specification  

ITEM

 TTA111AVT TTA111VT
Video input 1 Vp-p, 75 Ohms (BNC connector)
DC input DC12V
DC output for CCD camera DC 12V Regulate, 300mA(max)
Power consumption 40mA(max)
Dimensions W x H x D mm 109x77x24 49x42x45

Specification

ITEM

 TTA111AVR TTA111VR
Video input 1 Vp-p, 75 Ohms (BNC connector)
DC input DC12V
Power consumption 40mA(max)
Video gain adjusting Press1  0~300M
　 Press2  300~600M
　 Press3  600~900M
　 Press4  900~1200M
　 Press5  1200~1500M
Recommended cable CAT-5 UTP Cable 4 pair (AWG24)
Dimensions W x H x D mm 109x77x24 49x42x45
Note: Recommend STP (Shielding Twisted Pair) cable and use surge protector SP003/SP004 to avoid the damage of twisted pair system under lightning, thunderstorm weather environment.

Application:

TTA111AV, TTA111V both are active (amplified) devices that allow transmission of real-time color or monochrome audio & video signal, data up to 2400 meters over industry CAT 5 twisted pair networking cable.   Perfect for CCTV in need of long cable runs between buildings and utilizing existing wiring in large facilities.  A pair of wires is also dedicated for security alarm or pan/tilt/zoom data applications.  Selectable switch setting for cable length.  A remote DC power supply can provides power for 12VDC (24VAC-TTA111V) color or monochrome cameras via WT-104P cable.

TTA111VH Active Receiver With Extra Interference Rejection
Features: 

  • Built in a highly balanced mode of video transmission for extra interference immunity.

  • HF, MF, LF compensation for color gain and adjustable brightness & contract for cleaner, sharper looking picture.

  • Built in Input Impedance, Balance, Liner Gain adjustment.

  • Built in Surge Protection. 

  • Perfect to maintain good quality picture for long-range transmission with DVR.

  • Using two sets TTA111VT+TTA111VH for series connection, range up to 2.4Km(Color), 3Km(B/W).

TTA111VH
Specification
ITEM TTA111VH
Video input 0.12-2 Vpp
Input impedance 45-175 Ohms
Video output 1 Vpp, 75 Ohms
Freq. response 50 Hz - 5MHz (-3 dB)
Disturbance reduction > 70dB, 50Hz
Gain adjustment + 6 dB...+ 60 dB at 5MHz
Noise -50 dB at+40 dB gain adj.

-47 dB at+60 dB gain adj.

Power consumption DC 12V, 150mA (max)
Input protection Surge arrester
Indicators LED (Red)-power on

Distance (M)

 SW1 (1-8), SW2 (1-8)
0-300 X
300-600 SW1 (1, 2) to SW1 (1, 2, 3) up
600-900 SW1 (1, 2,3 ) to SW1 (1, 2, 3, 4, 5) up
900-1200 SW1 (1, 2, 3, 4, 5, 6) to SW1 (1, 2, 3, 4, 5, 6, 7, 8) + SW2 (1) up
1200-1500 SW1 (1, 2, 3, 4, 5, 6, 7, 8) + SW2 (1) to SW1 (1, 2, 3, 4, 5, 6, 7, 8) + SW2 (1, 2, 3, 4, 5) up
Material ABS
Dimension W x H x D mm 138x77x28

TTA414VR 4 Channel Active Receiver 

Features: 

  • Built in 4 port active receivers.

  • Others identical same as TTA111VR.

Specification

 FrontTTA414VR Front BackTTA414VR Rear
ITEM TTA414VR
Video input 1 Vp-p, 75 Ohms (BNC connector)
DC input DC 12V
DC output for CCD camera DC 12V Regulate, 300mA(max)
Power consumption 150mA (max)
Dimension W x H x D mm 138x66x28
　

OPTION:
To protect high value camera and CCTV image processor/monitoring equipment destroyed from high voltage surges from nearby lightning strikes, the long-range twisted pair cable go through outdoors. To add surge protection SP003-SP006 device on the back of camera and front of CCTV image processor / monitoring equipments. Small money to save high value CCTV equipments.

Securitex Electronic Systems Engineering

Block 9010 Tampines St 93 #04-145 Tampines Industrial Park A Singapore 528844 Tel: +65 67852171 Fax: +65 65850107  email: sales@securitex.com.sg

To purchase the above system or arrange for a site demo please contact us at the above number or email our technical personnel will contact you and discuss with you in more detail.

Back to Securitex Electronic Systems Engineering

Site Updated 1 January 2018