|
This page contains answers to
common questions handled by our support staff, along with some tips and
tricks that we have found useful and presented here as questions.
- General specifications of the
base unit
- General specifications of the
PIR [PIR-1]
- General specifications of the
GAS detector [ GA-1]
- General specifications of the
Smoke detector [SM-2]
- Numbers of zone available on the
LS9001A
- Numbers of remote control RC-1
allowed on one system
- What should I do if I lost the
RC-1 remote control
- How to tell that the battery of
the sensor is low
- How to program the auto dialer
to send a code to my pager.
- Why the system keep calling the
same number upon activation.
Specifications of base unit
- Input power:12VDC/300mA.
- Standby current :60mA
- Frequency : 433.9Mhz
- RF range: 159Ft@ open field and ambient temp
25C
- Security code: over 4.7millions
- Dialing type: Pulse/Tone
- Preset Telephone number: 9 numbers, max 32
digits for each number
- Voice recording: Total 29 seconds
- System activation : instant or 1-255 seconds
delay
- Password: 4 digits, user programmable
- Partial arming mode: Even/odd zone, PIR
disable
- Operation back-up time: 4 hours b internal
rechargeable battery
- Alarm output contact : 120Vac/3A rated relay
or 12Vdc/200mA
Specifications
of PIR
- Detector type: Dual elements, Passive infrared
- Coverage angle: 110 degree
- Effective distance : Max. 15M @ ambient
temp.25C
- Power : 9V battery
- Current: Stand by @12uA, 5mA @ operation
- Pulse count : 2 or 3 pulses selectable
- LED On/Off selection
Specification of GAS/LPG detector
- Power: 230Vac
- Power consumption : 2W max.
- Alarm sensitivity : 3300ppm for LPG
- Built in alarm buzzer and RF transmitter
- This detector is to locate 30cm above the
floor since LPG is heavier then air
- Detector can work alone without the base unit
.
Specification of smoke detector
- Detection : Photo-electric chamber
- Sensitivity : meet UL 217
- Power: 9V battery
- Operating Temperature: 0 - 50 C
- Relative Humidity: 10%-85%
- Size: Dia. 140mm x H 45mm
- Alarm sound level : 85dbm
- Indicator light: LED flashes every 45 seconds
- Current consumption : standby @4uA, Activation
@11mA
- Actuation indicator : LED on, Buzzer On, RF
transmission for FIRE
- Detector can work alone without the base unit
.
Number
of Zone on the LS9001A
- 9 burglary zone. Zone 1-9
- 2 fire zone , 4 detector in one zone. Fire 1,2
- one medical help zone. Zone 0
- one silence panic zone
Number
of Remote control allowed
- 8 numbers of RC-1 or KP-1 can be used on the
system
What to
do if RC-1 is lost
- From the base unit, cancel the code of
the RC-1. Replace a new RC-1 and relearned it.
Battery
low indication of sensor
- Door sensor (DS-1), PIR-1, Glass break sensor
(GB-1) would send an "alive" signal to the base init
periodically. If the base unit doesn't receive the signal for 4 hours
then the corresponding zone LED would flash to remind you to check the
sensor. In this case, remember to replace the battery first and press
the TEST button on the sensor to resume its work
- For Smoke detector, It will beeps periodically
if the battery goes too low.
Preset
Pager number
[F][4][pager
number ][C][*][code][*][*][memory no.]
To
Answer the Call from LS-9001A
- If the telephone number doesn't need any DTMF
tone acknowledgment, don't forget to say "hello" to respond
to the base unit so that the base unit know that this call is
successfully connected. Otherwise, the system will keep call this
number
- if the telephone number required a DTMF tone
acknowledgment, don't forget to press a key on your phone for the base
unit to identify this call is successfully connected.
- Refer to page 24 on the operation manual for
more details
For more Home Security System solution or question about intercom system
Click here |
